4th axis for CNC – MACH4 and PoKeys57CNC

4th axis for CNC – MACH4 and PoKeys57CNC

In this blog, we will describe, how we upgrade our CNC milling/router machine with the 4th axis for the CNC machine and get more functionality, how to set up, wiring components, and Configuration in Mach4. New upgrade in a machine shop with the intention to improve our support even additionally and also for making products for our development and needs.

If you have not installed and configured MACH4, follow the instructions in the step-by-step guide for Pokeys57CNC and MACH4. The configuration in the section below is additional steps for setting up in MACH4 with 4th axis CNC for your CNC machines.

Table of Contents


Installation and wiring components for CNC 4th axis

In the photo below – the wiring diagram it is shown components that were added into the CNC controller box for connection rotary axis stepper motor. So we add a stepper motor driver PoStep60-256 which is connected with a flat cable with existed CNC controllers PoKeys57CNC and with the stepper motor.

Wiring diagram- Pokeys57CNC-PoStep60-256-Stepper motor

Stepper motor parameters

For easier calculating and check all data, in the photo below is the data table. In the data table we insert data from the stepper motor:

  • deg/step
  • steps
  • pulse per step

All data about the stepper motor you get in the datasheet of the used motor.

On the rotary axis, we have also a reducer – different types. We have a planetary reducer and a gear reduction of reducer ratio we also add into a data table. For easier reading and using data table in the right side of the data table (undervalue) is showed how to use it.

Rotary axis-stepper motor parameters

Configuration in MACH4

When we have all data calculated, we start with insert – Configuration data into MACH4.

  • Firstly, set motor: Counts per unit is calculated value,
  • Secondly, set – enable rotary axis motor (A),
  • After control configuration, set- enable data in the plugin- pulse engine.

Control configuration

stepper motor configuration
MACH4-rotary axis-axis mapping
4th axis-Device configuration


Workpiece and rotary axis setup

The rotary axis has the following characteristic:

  • 550 mm working length (between jaw chuck and tailstock),
  • 4 jaw chuck (80mm diameter),
  • tailstock,
  • planetary reducer,
  • stepper motor Nema 23(SY57STH56-4004A).

The photo below is presented how the 4th axis is mounted on the CNC milling/router machine and how is oriented. When we mounting the rotary axis on the machine we must pay attention to:

  • The rotary axis must be correctly clamped on the CNC machine table,
  • Rotary axis must be perfectly aligned – coaxial to the axis Y or X,
  • check the working area of the CNC machine,
  • When mounting was finishing is important to set a zero point, usually, the zero points of Workpiece is in the middle of part-diameter,
  • When we programming the rotary axis we must pay attention to correct positions and safe movements near equipment and workpiece because all of us want to machining without collision.
Workpiece and rotary axis setup

Operation – rotary axis

We successfully mounted the 4th axis for the CNC router, correctly wire electronic components and configure MACH4. So we want to test the operation, write some G-code and check the rotation and the correct angle of turning (before check protocol set A axis to zero, it is important to get real data-measurements). So If all stepper motor parameter was correctly calculating and set into MACH4, the rotary axis will work properly. When you enable MACH4, you will now be able to use the referencing all axis, zero A-axis buttons, and jogging rotary axis.

4th axis for cnc router- rotating

4th axis – test part

Finally, we arrived at to test part. With upgrading the CNC machine with a rotary axis we want:

  • Firstly, more functionality on the machine,
  • Secondly, make some useful parts from different types of materials.



Share on facebook
Share on twitter
Share on pinterest
Share on linkedin

Leave a Reply

Your email address will not be published. Required fields are marked *

On Key

Related Posts

CNC Machines – A Quick Introduction

CNC Machines – A Quick Introduction

What is CNC? CNC Machines – A Quick Introduction, CNC stands for computer numerical control. It’s a term used whenever a computer handles machining operations and